This post down below pertaining to How to Install a Bathtub is seriously compelling. You should investigate it.
Mounting a bath tub isn't exactly rocket science, yet it does require solid plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old bathtub with a new one is also a moderately tough job. If the old bathtub is conveniently obtainable, the project can move speedily; if you need to open up a wall to remove the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the task as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This article will help you install a new bathtub in your bathroom if you have currently bought a brand-new bathtub and also do not require to transform the setup of your previous water pipelines.
Your tools as well as material checklist should comprise the following:
- New Bathtub
- Hammer
- Pipeline Wrenches
- Prybar
- Shatterproof glass
- Degree
- Pliers
- Flexible Wrench
- Putty Blade
- Screwdriver
- Cold Blade
- Tape Measure
- Pipeline Caps
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you must do is detach the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be rather bothersome because of the restricted gain access to that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a fabric ready for the staying water that will originate from the pipelines. When the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Before going on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin making sure that the washers are in place in between the tap and also the sink. Secure the tap in position with the manufacturer given backnut. When the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type ought to be attached to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Bath tub
Making use of both wooden boards under its feet, place the bathtub in the needed setting. The wood boards are handy in equally spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and adjusting the feet on the bathtub until the spirit level checks out level.
To install taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system and check all joints and new pipework for leaks as well as tighten them if required. Fill up the tub as well as likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the tub ought to wait up until the bathtub has been used at least once as this will certainly resolve it right into its last setting.
Getting ready for the Setup
First of all, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the maker's guidelines. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of both faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last position.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break an inflexible seal, causing the water to permeate the wall surface in between the bath as well as the tiling, causing difficulties with dampness as well as feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes and also cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to always fill up the tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealer can split rather very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily available on the market. It is recommended to fit the tiles utilizing water-resistant or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy more info about How to Install a Bathtub Yourself? Place feedback directly below. We would be glad to listen to your ideas about this posting. We are looking forward to see you back again in the near future. So long as you enjoyed reading our blog post if you please don't forget to share it. Many thanks for your time invested reading it.
Free Estimate
